top of page

(570) 660-9337

Serving Greater Pittsburgh, Allegheny, Washington, Fayette, Westmoreland, Indiana, Armstrong, Butler, Beaver

Are Two-Prong Outlets a Problem When Buying an Older House?

Writer: First Class Home Inspections
First Class Home Inspections
4 hours ago
7 min read

They can be a repair item because a two-prong outlet has no equipment ground, but the fixes are defined. InterNACHI's Standards of Practice have a home inspector inspect a representative number of receptacles and report, as in need of correction, any tested receptacle "where the receptacle was not grounded." CPSC's GFCI fact sheet says "A GFCI works even on two-slot receptacles," and that older ungrounded, two-slot receptacles can be replaced with new GFCI receptacles.

 

IAEI Magazine's article on the 2011 edition of the National Electrical Code describes three choices under Section 406.4(D)(2), the replacement rule for these outlets: another non-grounding receptacle, a GFCI receptacle marked "No Equipment Ground," or a grounding-type (three-slot) receptacle that is supplied through a GFCI and marked "GFCI Protected" and "No Equipment Ground." EC&M's article in the 2017 edition states the limit behind those labels: "An equipment grounding conductor shall not be connected from the GFCI type receptacle" to "any outlet supplied from the GFCI receptacle." A three-slot outlet installed this way gains GFCI shock protection but is still not grounded, and the label says so. Below: what inspectors check, the replacement choices and labels, adapters, GFCI testing and who does the work.


home inspection

What Is a Two-Prong Outlet, and What Does Ungrounded Mean?

 

A two-prong outlet is a two-slot receptacle with no grounding slot, the type electrical code articles call a nongrounding receptacle. CPSC's fact sheet calls them "older ungrounded, two-slot receptacles."

 

A three-slot receptacle is the grounding type, but the third slot alone does not make it grounded. For a grounded installation, Mike Holt's November 3, 2015 Code Q&A in EC&M says the receptacle's grounding terminal "must be connected to the circuit equipment grounding conductor in accordance with Sec. 250.130(C) or Sec. 406.4(C)." So "ungrounded" and "two-prong" are not the same finding: a three-slot outlet can be ungrounded too.

 

InterNACHI's Standards of Practice also have the inspector describe "the type of wiring observed," so a report can speak to the wiring as well as the outlets. For the wider question, see whether buyers should worry about old electrical wiring.

 

What Does a Home Inspector Check on Outlets?

 

InterNACHI's Standards of Practice, last revised in October 2022, set out three outlet tasks:

 

  • Inspect "a representative number of switches, lighting fixtures and receptacles."

  • Inspect "all ground-fault circuit interrupter receptacles and circuit breakers" that are "observed and deemed to be GFCIs using a GFCI tester, where possible."

  • Report as in need of correction any tested receptacle where power was not present, polarity was incorrect, the cover was not in place, the GFCI devices "were not properly installed or did not operate properly," there was "evidence of arcing or excessive heat," or the receptacle "was not grounded or was not secured to the wall."

 

Because the SOP calls for a representative number, the report speaks to the receptacles that were tested.

 

Buyers comparing approaches can read about electrical system inspections for Pennsylvania homebuyers, including standard versus comprehensive evaluations.

 

What Are the Code-Allowed Ways to Replace a Two-Prong Outlet?

 

IAEI's article on the 2011 NEC and Mike Holt's November 16, 2015 summary in EC&M describe the same three options under Section 406.4(D)(2):

 

Option

What replaces the two-slot outlet

Marking

(a)

Another nongrounding receptacle

None described

(b)

A GFCI receptacle

"No Equipment Ground"

(c)

A grounding-type (three-slot) receptacle supplied through a GFCI

"GFCI Protected" and "No Equipment Ground"

 

EC&M's February 2017 article on the 2017 NEC adds where the label can go: "The receptacle or the cover plate must then be marked 'No Equipment Ground.'" It also notes that "many customers would prefer to have a 3-pronged grounding-type receptacle instead of the 2-pronged type," which is where option (c) comes in.

 

One limit applies to new work. Mike Holt's November 3, 2015 Code Q&A says "The permission to replace nongrounding-type receptacles with GFCI-protected grounding-type receptacles doesn't apply to new receptacle outlets that extend from an existing outlet box that's not connected to an equipment grounding conductor."

 

Which code edition and local amendments apply to a given house is a question for the municipality's code office and the electrician doing the work.

 

Why Does a Three-Prong Outlet on a GFCI Say "No Equipment Ground"?

 

Because it is not grounded. IAEI's article on the 2011 NEC says that when a GFCI receptacle replaces the two-slot outlet, "no grounding connections are to be made to the GFCI or any outlets supplied downstream of the GFCI." When three-slot receptacles are fed through a GFCI instead, "no equipment grounding conductor is permitted to be connected between the grounding type receptacles used in this case." The GFCI adds shock protection; it does not add a ground.

 

CPSC gives the purpose of the sticker: it is there "to identify that the receptacle is not grounded." Its fact sheet says installers "Must use supplied label" and prints one combined label, "NO EQUIPMENT GROUND GFCI PROTECTED."

 

North Carolina's Office of the State Fire Marshal splits the labels by option in a February 2018 interpretation of Section 406.4(D)(2) of what it cites as the 2014 Electrical Code. A GFCI-type replacement receptacle gets "NO EQUIPMENT GROUND" only, while a receptacle that is not a GFCI but is protected by one gets both labels. That is North Carolina's reading; the local code office answers for a house in Allegheny County or elsewhere in Western PA.

 

Do Three-Prong Adapters Make a Two-Prong Outlet Safe?

 

ESFi's guidance turns on whether the adapter is grounded. Its Indoor Electrical Safety Check booklet (2004) says to "Use a properly grounded 3-prong adapter for connecting a 3-prong to a 2-hole receptacle" and to "Make sure the adapter ground wire or tab is attached to the outlet ground." If the inspection lists a receptacle as not grounded, there may be no outlet ground for that tab to reach. A licensed electrician can confirm.

 

The same booklet is direct about plugs: "Never remove the grounding feature on a plug by clipping or grinding off the third prong."

 

Its safety checklist also asks "Do you hear crackling, sizzling or buzzing from your outlets?" If an outlet buzzes, crackles or looks discolored, leave the cover plate on and call a licensed electrician. Do not take the outlet apart.

 

How Do You Test a GFCI, and How Often?

 

CPSC's fact sheet says a GFCI "constantly monitors current flowing through a circuit" and interrupts power when the current going out and the current coming back differ by "as little as 0.006 amperes." In CPSC's words, it "interrupts power faster than a blink of an eye."

 

CPSC's schedule is to "Test every GFCI:" after installation, "At least once a month," "After a power failure," and as the maker's instructions say. ESFi agrees: "GFCIs should be tested every month to ensure they are in working order."

 

ESFi's How to Test a GFCI sheet uses a nightlight plugged into the outlet: "Press the TEST button." Then, "The nightlight should turn OFF." If it stays lit, "the GFCI is not working properly."

 

ESFi notes that "Malfunctioning GFCIs do not provide shock protection." For a failed test, its advice is to "Have a licensed, qualified electrician check the GFCI and correct the problem if your GFCI is not working."

 

Who Should Fix Two-Prong Outlets After the Inspection?

 

A licensed electrician. ESFi says "GFCIs should only be installed by a licensed, qualified electrician," and the 406.4(D)(2) options that IAEI and EC&M describe for the 2011 and 2017 editions call for decisions made on site: which option fits each outlet, where GFCI protection starts, and how each receptacle or cover plate is marked.

 

A practical order for buyers:

 

  1. Find the receptacles the report lists as not grounded, with incorrect polarity, or with GFCI devices that did not operate properly.

  2. Have a licensed electrician evaluate those circuits and recommend a replacement option, or say whether a circuit can be grounded.

  3. Take the electrician's findings to your agent, who can explain how a repair request or credit fits your agreement. Here is what repairs buyers can ask for after an inspection.

  4. Before closing, check that replaced outlets carry the markings the chosen option calls for.

 

Outlets are one item on a longer list in an older house. See what inspections older Pittsburgh homes need.

 

FAQ

 

Can you replace a two-prong outlet with a three-prong outlet without a ground wire?

 

Under Section 406.4(D)(2), as IAEI (2011 NEC) describes it, a grounding-type receptacle is allowed if it is supplied through a GFCI and marked "GFCI Protected" and "No Equipment Ground." The outlet is still not grounded. A licensed electrician decides whether that option fits the circuit.

 

What does "No Equipment Ground" on an outlet mean?

 

The receptacle is not grounded. CPSC says that is what the label is there to identify.

 

How often should a GFCI be tested?

 

CPSC says at least once a month, after a power failure and after installation; ESFi also says monthly. If pressing TEST does not turn off a plugged-in nightlight, ESFi says the GFCI is not working properly and a licensed electrician should check it.

 

Is a three-prong adapter safe on a two-prong outlet?

 

ESFi says to use a "properly grounded" adapter with its ground wire or tab attached to the outlet ground. On an outlet the report lists as not grounded, ask a licensed electrician whether there is any ground for the tab to reach.

 

Does the GFCI replacement permission cover new outlets added from an old ungrounded box?

 

No, according to Mike Holt's November 2015 Code Q&A in EC&M. The permission to use GFCI-protected three-slot receptacles covers replacements, not new receptacle outlets extended from an existing box that has no equipment grounding conductor.

 

Older Home Inspections Near Pittsburgh From First Class Home Inspections

 

First Class Home Inspections is a home inspection company based in Pittsburgh, PA, with InterNACHI Certified Professional Inspector certification, serving Greater Pittsburgh and Allegheny, Washington, Fayette, Westmoreland, Indiana, Armstrong, Butler and Beaver Counties. Its single family home inspection covers the electrical system along with the roof, foundation, plumbing, HVAC, attic and interior living areas. When outlets need work, the company refers clients to a vetted network of contractors that includes electricians, and a follow-up inspection can verify the contractor's corrections.

 

Visit First Class Home Inspections or call (570) 660-9337 today. Contact us for more information.


First Class Home Inspections

 
 
 

Comments


bottom of page